歡迎光臨斯派特激光官方網站!
斯派特英文站English 斯派特西班牙文站Espaol 斯派特小语种站Português 斯派特小语种站Pусский 斯派特小语种站 斯派特中文站繁體中文

大胆西西人艺人术動態

News

激光器,co2激光器,激光器大胆西西人艺人术厂家 激光器,co2激光器,激光器大胆西西人艺人术厂家 激光管,co2激光管,激光管批发 二氧化碳激光管,激光管大胆西西人艺人术厂家 聚焦鏡,co2聚焦鏡 反射鏡,激光反射鏡 激光電源,co2激光電源批发
公司大胆西西人艺人术

斯派特激光溫馨提示:防凍液使用不當也會損壞激光管!

點擊: 次來源:www.sptlaser.com 時間:2017-11-22

冬天來了啊,激光管激光器等如何做好防凍措施
冬天來了啊,激光管激光器等如何做好防凍措施


尊敬的斯派特激光用戶:

                                           您好!
 

    近期受大胆西西人艺人术大范围冷空气影响,各区域都有明显降温现象,激光管水冷机温度过低,有可能会导致水冷机故障及管路结冰,因冰的密度小于水的密度,故会导致水冷机及激光管內部因體積膨脹而造成玻璃破裂,從而導致相關核心部件的重大損害,所以特別提醒您做好相關的預防工作,具體防凍措施請參見下文。

 

一、防凍基本措施

为避免冷却液体凝固导致激光管、水冷机损坏,推荐以下3个解決方案:

1.保證工廠決不會斷電的情況下,夜間不關閉水冷機,保證冷卻液處于循環狀態。

2.每天使用完畢後將激光管、水冷機內冷卻液體排空。

3.使用激光管廠家指定防凍液作爲冷卻液。
 

专注激光器大胆西西人艺人术和研发的厂家

 

二、注意:

使用激光管廠家指定防凍液作爲冷卻液,不然會激光管帶來損壞!

當使用環境經常停電以及不具備每天冷卻液排空的條件,則必須使用防凍液,推薦選擇CLARIANT(科萊恩)品牌,適用于激光系統中的防凍液有兩個型號:

1) Antifrogen®N (工业用品)

2) Antifrogen®L  (食品级)

 

激光器激光管防冻液
 

其添加比例是3:7 (3为防冻液,7为水),添加防冻液之后能抵抗-20℃而不结冰

其他品牌有做過測試比如長城牌型號:FD-1,對激光管有損壞,用了此防凍液工作中的激光管,在出光的過程中激光光束不穩定,激光管內發出異響,功率下降10瓦以上,激光管鍍膜膜層收損導致光白,壽命直接受到影響!後期我公司會對其他更多防凍液進行測試讓客戶有更多的選擇!

 

三、爲保證水路通暢添加防凍液首先要保證水箱清潔:

1. 将使用过的水放掉清洁水箱内壁及滤网加入清水冲洗将污渍冲走;

2. 将滤芯水杯拆除清洁水杯及更换滤芯(注意滤芯水杯有无密封圈切勿丢失);

3任何防凍液不能完全替代去離子水,不能全年長時間使用。冬天過後必須用去離子水或純淨水清洗管路,並恢複使用去離子水或純淨水作爲冷卻劑。

如果有條件的情況下,我們仍建議改善用電環境,保持水冷機不關機。

如長時間不用激光切割機,只要是冷卻水經過的地方,尤其是激光管內部和管路中的冷卻水,必須徹底放幹淨。

以上說明客戶未嚴格執行,造成激光管或冷水機損壞自行承擔責任,請您重視!!

如果有不明之處,請致電我司咨詢。
 

斯派特激光研發人員正在對激光器進行檢測
斯派特激光研發人員正在對激光器進行檢測

 

Dear customers of SPT laser:

The global temperature goes down obviously inthe past few weeks. If ambient temperature is too low, it may result in waterfreeze inside of co2 glass laser tube & water chiller and broken them. Sowe have to take more precautions, the following 3 solutions for options:

1. To keep water chiller working with no stop 24 hours and making surethe water flowing continuously.

2. Draining water away from the water chiller and glass laser tube aftermachine working every day

3. Adopts anti-freeze fluid asour recommended

Attention:  Please adopt recommendedanti-freeze fluid,otherwise may damage the lasertube.

If the above solution 1 or solution 2are can not be adopted, then anti-freeze fluid will be necessary. We recommendbrand “CLARIANT”, and its 2 models are suitable for laser products

 

1) Antifrogen®N 

2) Antifrogen®L  

 

The adding ratio is 3:7 (3 for anti-freeze fluid, 7 for cooling water),it will not be freezed under temperature -20℃

But other brand of anti-freeze fluid such as SINOPEC: FD-1may cause laser tube damage such as unstable laser beam, abnormal noise, laserpower decreasing more than 10watt and lifetime reduction. In the coming futurewe will do more testing on other brand of anti-freeze fluid to get more optionsfor customers.

Cleanthe water chiller before adding anti-freeze fluid

1.Drain water away from water tank and then clean the limescale

2.Exchange the filter of water chiller if necessary

3.When winter pass and temperature up, the water with anti-freeze fluid hasto be changed to purified water again.

If laser machine will not be used for a long time, thewater inside of laser tube, water chiller and water pipes should be drainedout, especially for glass laser tube. If buyer did not carry out ourinstruction, any broken of laser tube cased by this will not be guaranteed. 
 

斯派特激光工作人员

 

斯派特激光官方微信    微信号:SPTlaser     网址:www.sptlaser.com

斯派特激光微信公众号二维码

 

大胆西西人艺人术服务大胆西西人艺人术: 0769-26380380